FAST BARANEK fine polymer-mineral plaster, roughcast structurised 25 kg

Availability: duża ilość
Dispatched within: 5 dni
Price: 49,09 zł 49.09
quantity szt.

product unavailable

add to wish list
Rating: 5
Vendor: FAST
Product code: BARANEK (minerał) 25kg

Description

fine polymer-mineral plaster, roughcast structurised 
________________________________________
 
Application
FAST BARANEK is used for manual or mechanical  performance of fine, thin-layer mortars inside and outside the building. It can be used on any mineral surface that is strong and even enough (cement, cement-lime plasters, concrete, reinforced layer in ETICS FAST S, FAST W, ECOROCK G / FASROCK G thermal insulation systems).


Properties
FAST BARANEK is a dry mineral mixture with the addition of selected quartz aggregate and plasticizers to facilitate the application and adhesion of plaster coating to the substrate. It is characterized by high water vapor permeability and high water resistance after complete binding. It does not contain  lime, thus limiting the risk of efflorescence.

Packaging
a sack - 25 kg
 
________________________________________
 
Preparation of the surface
The surface should be even, strong and dry, free from all kinds of contamination that reduce the adhesion of the grip, i.e. dust, lime, grease, and remains of old paint coatings. In order to reduce absorbency, the surface should be primed with one of FAST's grounds. Regardless of the type of surface, it is necessary to prime it with FAST GRUNT M. before each application.
Plaster mortar can be used on following surfaces:
• cement and cement-lime plasters (after a minimum of 28 days from the implementation and humidity not higher than 4%) primed with FAST GRUNT M
• concrete (after more than 3 months from the implementation and humidity not higher than 4%) primed with LAST GRUNT M - gypsum substrates (humidity <1%) primed with FAST GRUNT G and FAST GRUNT M
• a layer in the insulation system reinforced with a mesh, made on FAST SPECJAL mortar and primed FAST GRUNT M over 3 days
• primed lamellar boards in the FAST W-G system
________________________________________
 
Preparation and use
The content of the bag should be mixed mechanically with about 5.0 liters of clean water until a homogeneous paste of assumed consistency is obtained. Leave this mixed mass for about 10 minutes and mix thoroughly again (do not add water), use within 1 hour. We apply a thin layer (grain thickness) on a suitably prepared and primed substrate using a stainless steel trowel. After a short time depending on the conditions at the time of application, we can start shaping the surface with a plastic trowel. When applying plaster, we adhere to the general rule by applying "wet on wet". If the mixture thickens during this time, stir again intensively without adding water.
Tools and container should be clean. The plaster can also be applied by spraying, which  increases its efficiency and shortens the time of work. Due to the specificity of the product it is recommended to use plastering machines equipped with a screw pump, i.e. WAGNER PC 35 or PC 15. When applying and drying plaster, observe the appropriate weather conditions, ie the temperature of the substrate and the environment from + 5 ° C to +25 ° C, lack of strong sunlight, rain and too high relative humidity above 75%. The drying time of the plaster at an optimum temperature of + 20 ° C is from 12 to 36 hours. Painting plaster with silicate paints can start after drying, but not earlier than after 3 days. Silicone paints can be applied after 14 siloxane and acrylic ones after a minimum of 28 days.
 
________________________________________
 
Technical data
Base unit: kg
Base: a dry mineral mixture with the addition of selected quartz aggregate and plasticizers
Mixing ratio: 5.0 to 5.5 l for 25 kg of dry matter
Density of mortar after making water: about 1.8 kg / dm3
Open time: about 20 minutes
Standby time: up to 1 hour
Adhesion to concrete: min. 0.3 FP: B MPa
Substrate and ambient temperature: from +5 to +25 degrees Celsius
Resistance to temperatures: from -20 to +60 degrees Celsius
Soluble chromium VI content: not more than 0.0002%
Reaction to fire class: A1
Water vapor permeability: μ 15/35 (tabular value
Heat transfer coefficient: 0.67 (tabular value) W / mk
Compressive strength after 28 days: ≥ Category CS II (1.5-5.0 N / mm2) MPa
 
________________________________________
Storage and comments
Store in factory-sealed packages in dry rooms at temperatures between + 5 ° C and + 25 ° C. Shelf life is 12 months.
The recommended product or the method of implementation does not exempt the contractor from carrying out work in accordance with the construction works and health and safety rules. P.W. FAST guarantees and bears responsibility for the quality of the product, while it does not affect the way it is used and the conditions in which it was used. All technical data were measured in normal conditions in temperatures of + 20 ° C and 60% relative humidity. In case of other conditions than the above, the drying time may change, i.e. lengthen or shorten.


This card replaces all previous versions.


During work, avoid direct contact with the skin and protect eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Immediately wash contaminated skin with plenty of water. Keep away from children.
The product conforms to the European Technical Approval: ETA-14/0464 and ETA-14/0465. It has the ETA certificate of conformity: 1020-CPR-020-032349 and 1020-CPR-020-032351 The product conforms to the ITB Technical Approval: AT-15-9715 / 2016. Has a valid hygienic certificate. The product complies with the PN-EN 998-1: 2004 standard
The component of the ETICS FAST S and FAST W thermal insulation system and the ITB ECOROCK G / FASROCK G. garage system.

 

Product reviews (0)

up
Shop is in view mode
View full version of the site
Sklep internetowy Shoper.pl