FAST Baranek thin-layer, silicone plaster mix 15 kg

Availability: duża ilość
Dispatched within: 5 dni
Price: 119,00 zł 119.00
quantity szt.

product unavailable

add to wish list
Rating: 5
Vendor: FAST
Product code: Baranek (silikon) 15kg

Description

Thin-layer, silicone plaster mix
 
________________________________________
 
Application
FAST BARANEK SIL is used for manual fine, thin-layer plaster mix both inside and outside the building. It can be used on each mineral surface that is strong and even enough (cement, cement-lime plasters, concrete, sandstone) and covered with well-gripped paint coatings.


Properties
FAST BARANEK SIL is a ready to use product based on a dispersion of silicone and acrylic-styrene resins with the addition of a siloxane emulsion. It creates a coating strongly bound to the surface, characterized by high vapor permeability. Due to the surface hydrophobization FAST BARANEK SIL has a reduced wettability limiting the penetration of water with substances dissolved in it. The plaster has a high resistance to soiling and the development of microorganisms such as algae and fungi. Particularly recommended in building insulation systems using mineral wool. Supplied in a rich palette of colors according to FAST COLOR SYSTEM. It contains agents eliminating the growth of algae and fungi on the surface of the plaster.


Packaging
bucket - 15 kg
 
________________________________________
 
Preparation of the surface
The surface should be even, strong and dry, free from all kinds of contaminants that reduce the adhesion of the trip, ie dust, lime, grease, remains of old paint coatings. In order to reduce absorptivity, the surface should be primed with FAST GRUNT G. To increase the adhesion of the plaster, it is necessary to prime FAST GRUNT M. before each application. It is recommended to apply a primer in the shade of the selected FAST BARANEK SIL color.
Plaster mass can be applied to the following  surfaces:
• cement and cement-lime plasters (after a minimum of 14 days from the implementation and humidity not higher than 4%) primed with FAST GRUNT M
• concrete (after more than 3 months from the application and humidity not higher than 4%) primed with FAST GRUNT M
• gypsum surfaces (humidity <1%) primed with FAST GRUNT G and FAST GRUNT M
• layer in the insulation system reinforced with mesh, made on FAST SPECJAL mortar and primed FAST GRUNT M over 3 days
________________________________________
 
Preparation and use
Before applying the plaster, the contents of each package should be mixed using a low-speed drill in order to equalize the consistency. Apply the plastering mix with a stainless steel trowel. After a short time, you can shape it using a plastic trowel. Rub the plaster with circular moves. When applying the plaster, follow the general rule by applying "wet on wet". It is also possible to apply this plaster using the spray method, which significantly reduces the cost and time of application. Details on the exact technology are available at www.fast.zgora.pl.

Tools and container should be clean. When applying and drying the plaster, observe the appropriate atmospheric conditions, i.e. the temperature of the substrate and the environment from + 5 ° C to + 25 ° C, lack of strong sunlight, rain and too high relative humidity above 75%. The drying time of the plaster at an optimum temperature of + 20 ° C is from 12 to 48 hours.
 
________________________________________
 
Technical data
Base unit: kg
Base: aqueous dispersion of silicone and styrene-acrylic resins with the addition of siloxane emulsion, mineral fillers and pigments
Open time: about 20 minutes
Drying time: from 12 to 48 hours
Substrate and ambient temperature: from +5 to +25 degrees Celsius
Resistance to temperatures: from -20 to + 60 degrees Celsius
VOC content: below 30 g / l
Water absorption w24: ≥ 0.1 ≤ 0.5 kg / m2
Bulk density: about 1.8 kg / dm3
Adhesion to concrete: min. 0.8 MPa
Water vapor permeability: μ [V2]
 
________________________________________
Storage and comments
Store in original packaging, in dry rooms at temperatures between + 5 ° C and + 25 ° C.
Additional comments:
o Before applying, confirm color compatibility with the order. After the product has been applied, complaints regarding the color will not be considered.
o to avoid differences in shades on one architectural surface, work should be carried out without interruption, using plaster packages, previously mixed with each other in a large castrm.
o Protect the plaster against unfavorable atmospheric conditions by means of scaffoldings until they are completely dry.
The recommended scope of use of the product or the method of implementation does not exempt the contractor from performing works in accordance with the construction arts and health and safety rules.

P.W. FAST guarantees and bears responsibility for the quality of the product, however it does not affect the way it is used and the conditions in which it was used. All technical data have been measured under normal conditions, i.e. at + 20 ° C and 60% relative humidity. In the case of other conditions than the above, the drying time may change, i.e. lengthen or shorten.
This card replaces all previous versions.
During work, avoid direct contact with the skin and protect the eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Immediately wash contaminated skin with plenty of water. Keep away from children.
The product conforms to the European Technical Approval: ETA-14/0464 and ETA-14/0465. It has the ETA certificate of conformity: 1020-CPR-020-032349 and ETA: 1020-CPR-020-032351. It has a valid hygienic certificate. The component of the ETICS FAST S and ETICS FAST W ETICS insulation system

 

Product reviews (0)

up
Shop is in view mode
View full version of the site
Sklep internetowy Shoper.pl