FAST GRANIT is used for manual thin-layer, mosaic plastering inside and outside the building. It can be used on any mineral surface that is strong and even enough (cement, cement-lime plaster, concrete, gypsum plasterboard, reinforced layer in the FAST thermal insulation system). It is recommended for surface finishing pedestals, underpinning, balcony balustrades, fence elements, etc. It is also intended for cladding on walls of staircases, corridors, living and utility rooms due to its aesthetic values and high durability, resistance to cleaning, washing and abrasion, properties
FAST GRANIT is a ready to use product based on acrylic dispersion with the addition of natural granite or colored quartz or marble aggregates. It is characterized by increased resistance to atmospheric pollution, high durability, washability and impact resistance. It is vapor-permeable and hydrophobic. It is available in a wide range of color combinations: FAST GRANIT MARMO, FAST GRANIT QUARZO, FAST GRANITE NATURA or FAST GRANIT MINI.
A bucket - 15 kg
Preparation of the surface
The surface should be even, strong and dry, free from all kinds of impurities that reduce the adhesion of the mortar, i.e. dust, lime, grease, and remains of old paint coatings. In order to reduce absorptivity, the surface should be primed with FAST GRUNT G. Regardless of the type of surface, the plaster should be primed with FAST GRUNT M to increase the adhesion of the plaster. It is recommended to use a primer in a shade similar to the chosen FAST GRANIT color.
The mortar can be used on following surfaces:
• cement and cement-lime plasters (after a minimum of 28 days from the application and humidity not higher than 4%) primed with FAST GRUNT M
• concrete (after more than 3 months from the application and humidity not higher than 4%) primed with FAST GRUNT M
• gypsum surfaces (humidity <1%) primed with FAST GRUNT G and FAST GRUNT M
• a layer in the insulation system reinforced with a mesh, made on FAST SPECJAL mortar and primed FAST GRUNT M over 3 days
Preparation and use
Before applying the plaster, the contents of each package should be mixed with a slow speed mixer in order to equalize the consistency. In the case of too dry mass, it is allowed to add water in the amount of 100 to 150 g. On previously prepared and primed substrate, apply a plaster mass in a thin layer, the thickness of the aggregate using a stainless steel trowel. Then level the entire surface with 2-3 strokes in one direction. Just like with colored acrylic plasters, we adhere to the principle of applying "wet on wet".
Tools and container should be clean. When applying and drying the plaster, observe the appropriate atmospheric conditions, ie the temperature of the substrate and the environment from + 5 ° C to + 25 ° C, lack of strong sunlight, rain and too high relative humidity above 75%.
Base unit: kg
Base: acrylic dispersion with the addition of selected granite aggregate or interchangeably colored marble / quartz
Time of work: about 20 minutes min
Drying time: from 12 to 48 hours
Substrate and ambient temperature: from +5 to +25 degrees
Diffusion resistive resistance sd: max 0.3 m
VOC content: below 30 g / l
Bulk density: approximately 1.9 kg / dm3
Storage and comments
Store in factory-sealed packages in dry rooms at temperatures between + 5 ° C and + 25 ° C.
o to avoid differences in shades on one architectural surface, work should be carried out without interruption, using plaster packaging, previously mixed with each other in a large castrm.
o too intensive mixing of the plaster with a high-speed drill and conducting work in highly sunny places can lead to defects on the surface of the mosaic.
o protect the plaster against unfavorable atmospheric phenomena by means of scaffoldings until they are completely dry.
o too strong surface smoothing during plastering can lead to the formation of abrasive rubbing.
o mosaic plaster should not be applied on horizontal surfaces or those with a slight slope
o high humidity and constant contact with water can cause "milking" of its surface, which disappears after drying. This is the natural behavior of this product and is not a subject to complaint.
o Before applying, confirm color compatibility with the order. After applying the product, complaints regarding the color will not be considered.
Recommended and specified in the card the scope of application of the product or the method of execution does not relieve the contractor from carrying out works in accordance with
construction and health and safety rules.
P.W. FAST guarantees and bears responsibility for the quality of the product, while it does not affect the way it is used and the conditions in which it was used. All technical data were measured under normal conditions, i.e. at + 20 ° C and 60% relative humidity. In the case of other conditions than the above, the drying time may change, i.e. lengthen or shorten.
This card replaces all previous versions.
During work, avoid direct contact with the skin and protect the eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Immediately wash contaminated skin with plenty of water. Keep away from children.
The product complies with the European Technical Approval: ETA-14/0464 and ETA-14/0465. It has an ETA certificate of conformity: 1020-CPR-020-032349 and 1020-CPR-020-032351. Has a valid hygienic certificate. The component of the ETICS FAST S thermal insulation system and ETICS FAST W.